Other

No. 280

No. 280 H.D. Air Lifter

The Air Lifter moves heavy appliances up to 800 lbs. by generating high pressure jets through its perforated rubber load plates. Slide the load plates under the load, turn on the blower, and the air plates inflate to lift the load. The air jets beneath create a cushion of air that glides the load over hard surfaces like vinyl or hardwood without scratching. Comes with a set of four smooth polypropylene pads for moving the load plates over carpet. Saves time and reduces the risk of damaging new floors as well as injuries! Includes: 2 air plates, 2 horsepower blower with shoulder strap, T-connector, 3 hoses, 4 carpet pads, and 2 carrying bags. Volts: 120VAC - Amps: 7.5. Net weight: 30 lbs.

No. 235

No. 235 6" Disposable Cove Base Nozzle

These inexpensive 6" disposable cove nozzles fit over the applicator tip of common base adhesive cartridges. They evenly spread five beads of adhesive for optimal application onto 6" wide cove base. The five holes are spaced to apply adhesive so that adhesion is maximized and overflow from the edges of the base is minimized. The hole diameters are sized to ensure that an equal amount of glue is dispensed from each hole. The end flange fits behind the nozzle slot of most popular guns and prevents the nozzle from coming off the cartridge tip. Includes one each disposable nozzle. Net weight: 1 oz.

No. 236

No. 236 3" Disposable Cove Base Nozzle

These inexpensive 3" disposable cove nozzles fit over the applicator tip of common base adhesive cartridges. They evenly spread three beads of adhesive for optimal application onto 3" wide cove base. The three holes are spaced to apply adhesive so that adhesion is maximized and overflow from the edges of the base is minimized. The hole diameters are sized to ensure that an equal amount of glue is dispensed from each hole. The end flange fits behind the nozzle slot of most popular guns and prevents the nozzle from coming off the cartridge tip. Includes one each disposable nozzle. Net weight: 1 oz.

No. 237

No. 237 Quart Cove Base Gun

This gun takes standard quart cove base adhesive cartridges. The smooth pushrod delivers continuous feed and pressure. Rod pressure is released for reloading or for stopping the flow using an easy-access thumb lever. A handy cutter is built in to the handle to cut the end off the plastic tip of the cartridge. A riveted 5 ½" long needle pivots out from the body to break the cartridge seal through the tip of the cartridge. Durable and economical all-steel construction. Includes gun only - no adhesive cartridge is included. Net weight 2 ½ lbs.

No. 238

No. 238 1/10 Gallon Cove Base Gun

This gun takes standard 1/10 gallon cove base adhesive cartridges. The smooth pushrod delivers continuous feed and pressure. Rod pressure is released for reloading or for stopping the flow using an easy-access thumb lever. Durable and economical all-steel construction. Includes gun only - no adhesive cartridge is included. Net weight 1 1/4 lbs.

No. 532

No. 532 Topset Gouge

The topset gouge forms a 5/32" wide groove on the back side of vinyl or rubber cove base to produce tight-wrapped corners. The groove removes excess fullness at the corner that can cause the base to pucker and form gaps from the wall. Grooving depth is adjustable using the knurled steel nut. Wood handle is rounded to fit the palm comfortably. Blade is replaceable and resharpenable (No. 533). Net weight: 3 oz.

No. 533

No. 533 Replacement Blade

Includes one each replacement blade only for the Crain No. 532 Topset Gouge used to form a 5/32" wide groove on the back side of vinyl or rubber cove base to produce tight-wrapped corners. The groove removes excess fullness at the corner that can cause the base to pucker and form gaps from the wall. Blade is resharpenable. Net weight: 1 oz.

No. 038

No. 038 3" Economy Notched Spreader

The No. 038 is a 3" wide spreader for spreading base adhesive across the back of 4" wide vinyl or rubber cove base. The 1/8" x 1/8" V-shaped notches are typically the correct size notch for spreading this adhesive (check manufacturer's recommendations). The blade is made from brushed spring steel that has the right amount of flex for spreading adhesive. Blade is riveted to a wide contoured plastic handle. Net weight: 2 oz.

No. 039

No. 039 4" Economy Notched Spreader

The No. 039 is a 4" wide spreader for spreading base adhesive across the back of 6" wide vinyl or rubber cove base. The 1/8" x 1/8" V-shaped notches are typically the correct size notch for spreading this adhesive (check manufacturer's recommendations). The blade is made from brushed spring steel that has the right amount of flex for spreading adhesive. Blade is riveted to a wide contoured plastic handle. Net weight: 3 oz.

No. 040

No. 040 3" Notched Spreader

The No. 040 is a top quality 3" wide spreader used for spreading base adhesive across the back of 4" wide vinyl or rubber cove base. Features a polished stainless steel blade and an attractive lacquered wood handle. The blade has 1/8" x 1/8" V-shaped notches which are typically the correct size for spreading this adhesive (check manufacturer's recommendations). Blade has just the right amount of flex for spreading adhesive. Net weight: 2 oz.

No. 041

No. 041 4" Notched Spreader

The No. 041 is a top quality 4" wide spreader used for spreading base adhesive across the back of 6" wide vinyl or rubber cove base. Features a polished stainless steel blade and an attractive lacquered wood handle. The blade has 1/8" x 1/8" V-shaped notches which are typically the correct size for spreading this adhesive (check manufacturer's recommendations). Blade has just the right amount of flex for spreading adhesive. Net weight: 2 oz.

No. 197

No. 197 "Comfort Knees" Knee Pads

Made especially for carpet installation, these pads provide protection for both kneeling and knee kicking, so they stay on at all times. The extra wide straps won't pinch your legs, even when wearing shorts. The contour conforms to the motion of your knee whether walking, kneeling, or kicking. Made from flexible yet durable neoprene material, these pads are machine-washable. Inner knee pad is replaceable. Net weight: 1 lb./set.

No. 199

No. 199 Polyurethane Skin Comfort Knees

The polyurethane skin on the kneeling surfaces of these pads prevent build-up of sharp items such as splinters that can scratch floors. The polyurethane is also resistant to tearing and penetration, providing extra durability. Comfort Knees are designed for floor installation. They provide protection for both kneeling or knee kicking, and can stay on at all times. The extra wide straps won't pinch your legs. The contour conforms to the motion of your knee. Made from flexible yet durable neoprene material, these pads are machine-washable. Inner knee pad is replaceable. Net weight: 1 lb./set.

No. 206

No. 206 Leather Knee Pad Set

Leather knee pads have ultra-thick padding for greater kneeling comfort. The tough leather wear surface is very durable and minimizes build-up of sharp objects like splinters that can scratch floors. The thick felt inner padding is riveted to the leather. The thick leather straps and steel buckles are designed to last. Net weight: 1 3/4 lbs.

No. 200

No. 200 Elastic Strap Knee Pad Set

These genuine sponge-rubber knee pads are ½" thick to provide a good cushion feel and extra durability. The wide 1 ½" elastic straps reduce the uncomfortable pinching feel around the back of the leg, and include fast acting hook-and-loop fasteners. The elastic straps are easily adjustable and stretches as you move. Good quality and value in a knee pad! Net weight: 1 lb. / set.

No. 198

No. 198 Buckle Strap Knee Pad Set

These genuine sponge-rubber knee pads are ½" thick to provide a good cushion feel and extra durability. The ½ wide straps include durable hinge-activated buckles. To adjust the straps, simply insert the angled end of the strap into the buckle and press the lever down. Once fastened, the buckles hold tight. No hassles with carpet fuzz build-up like with hook and loop fasteners! Good quality and value in a knee pad! Net weight: 1 lb. / set.

No. 250

No. 250 Troxell Soft R Knee Pads

These ultra-soft knee pads are the Troxell regular/medium size in royal blue color. They are made from durable neoprene with polyurethane protective coating. The wide flexible straps won't pinch the back of the leg even when wearing shorts. The straps fasten to the front face of the pad using hook and loop fasteners. Inner pad is made from high density closed cell foam. This is Troxell product #17-209SOFT. Net weight: 11 oz. / set

No. 251

No. 251 Troxell Soft L Knee Pads

These ultra-soft knee pads are the Troxell size large in royal blue color. They are made from durable neoprene with polyurethane protective coating. The wide flexible straps won't pinch the back of the leg even when wearing shorts. The straps fasten to the front face of the pad using hook and loop fasteners. Inner pad is made from high density closed cell foam. This is Troxell product #17-209SOFTL. Net weight: 12 oz. / set

No. 252

No. 252 Troxell XL Leather Knee Pads

The Troxell "Leather Head" knee pads are made from durable neoprene with an extra tough leather protective covering. The wide flexible straps won't pinch the back of the leg even when wearing shorts. The straps fasten to the front face of the pad using hook and loop fasteners. Inner pad is made from high density closed cell foam. This is Troxell product #17-209SOFTXL. Net weight: 1 lb. / set

No. 344

No. 344 Score Tool

This carbide scoring tool marks a score line on plastic laminate or cementitious backer board so that it can be cleanly and easily broken along the score line. The contoured plastic handle holds the carbide tip at the optimal angle for scoring. The reversible blade includes two carbide tips. Blades are also replaceable (No. 345). Net weight: 4 oz.

No. 345

No. 345 Double Blade

Includes one each replacement blade for the Crain No. 344 Score Tool used to mark a score line on plastic laminate or cementitious backer board. After scoring, the material breaks along the desired score line cleanly and easily. The blade includes two carbide tips and is reversible in the handle of the No. 344 Score Tool. Net weight: 1 oz.

No. 346

No. 346 "J" Roller

This hand roller is designed for plastic laminate installation. The 3" wide solid rubber roller produces about 30 - 45 PSI for positive bonding of the laminate onto the substrate. The rubber roller material is non-marking. The offset handle and recessed axle and fasteners allow the roller to work closely to the wall without scratching. Net weight: 8 oz.

No. 845

No. 845 Metal Mitre Handle

Includes the handle assembly only for the family of Metal Mitre interchangeable die sets and handles used to make corner shapes in cap metal. This compound leverage handle generates the force necessary to punch notched shapes out of aluminum cap. Die sets fasten onto the cast iron die holder with two fasteners. This handle accepts the following interchangeable die sets: No. 846 (.135" thick punch - carpet / wall board cap), No. 848 (.090" thick punch - vinyl / carpet cap with at least 3/32" opening), No. 850 (.050" thick punch - vinyl / laminate cap with at least 1/16" opening). This handle also works as replacement handle for the die sets in a No. 870 Vinyl Notcher, though that die set is not sold separately. No die set is included with this handle. Net weight: 1 1/2 lbs.

No. 846

No. 846 Die Set

This interchangeable Metal Mitre die set only has an extra-thick .135" punch for mitering corner shapes in heavier cap metals, such as carpet cap or wall board cap. It can be used on any Metal Mitre handle (No. 845) to punch out the 90° notches necessary to form a corner. Adapts to the handles from the following combos: Nos. 847, 849, 851, 870. NOTE: this punch is too thick to enter the narrow channels of laminate and vinyl cap metals. For use on aluminum cap metal only. Replacement punch: Part No. 1846-A. Net weight: 8 oz.

No. 847

No. 847 Die Set w/Handle

This combo includes a handle and die set with extra-thick heavy-duty .135" punch for mitering heavier cap, such as carpet cap or wall board cap. Makes corner shapes fast from aluminum cap metals by punching out 90° notches necessary to form a corner. The compound leverage handle generates the large amount of force needed. NOTE: the punch for this combo is too thick to enter the narrow channels of laminate and vinyl cap metals. The handle from this combo accepts the following interchangeable die sets: Nos. 846, 848, and No. 850 (sold separately). Replacement punch: Part No. 1846-A. Net weight: 2.1 lbs.

No. 848

No. 848 Die Set

This interchangeable Metal Mitre die set only has a relieved .090" thick punch for mitering corner shapes in most vinyl and carpet cap metals with at least at 3/32" opening. It can be used on any Metal Mitre handle (No. 845) to punch out the 90° notches necessary to form a corner. Adapts to the handles from the following combos: Nos. 847, 849, 851, 870. For use on aluminum cap metal only. Replacement punch: Part No. 1848-A. Net weight: 8 oz.

No. 849

No. 849 Die Set w/Handle

This combo includes a handle and die set with relieved .090" punch for mitering most vinyl and carpet cap with at least a 3/32" opening. Makes corner shapes fast from aluminum cap metals by punching out 90° notches necessary to form a corner. The compound leverage handle generates the large amount of force needed. The handle from this combo accepts the following interchangeable die sets: Nos. 846, 848, and No. 850 (sold separately). Replacement punch: Part No. 1848-A. Net weight: 2.1 lbs.

No. 850

No. 850 Die Set

This interchangeable Metal Mitre die set only has a slender .050" thick punch for mitering corner shapes in most vinyl and laminate cap metals with at least at 1/16" opening. This slender punch can enter the narrower channels. It can be used on any Metal Mitre handle (No. 845) to punch out the 90° notches necessary to form a corner. Adapts to the handles from the following combos: Nos. 847, 849, 851, 870. For use on aluminum cap metal only. Replacement punch: Part No. 1850-A. Net weight: 8 oz.

No. 851

No. 851 Die Set w/Handle

This combo includes a handle and die set with thin .050" thick punch for mitering most vinyl and laminate cap with at least a 1/16" opening. The slender punch easily enters the narrow channels. Makes corner shapes fast from aluminum cap metals by punching out 90° notches necessary to form a corner. The compound leverage handle generates the large amount of force needed. The handle from this combo accepts the following interchangeable die sets: Nos. 846, 848, and No. 850 (sold separately). Replacement punch: Part No. 1850-A. Net weight: 2.1 lbs.

No. 870

No. 870 Die Set w/Handle

This specialty combo handle and die set has a .156" thick punch for use on vinyl T-moldings only. The punch quickly cuts out a relief notch from the insert of the T-molding with a 1/4" wide bottom and 45° side angles. After the relief notch is removed using this tool, the T-molding easily forms tight radius bends up to 90°, such as at the outside corners of a table top. The No. 870 is sold as a combo handle and die set only. The die set for the No. 870 is not sold separately. However, the handle from the No. 870 is interchangeable with the following die sets: Nos. 846, 848, 850 (sold separately). Replacement punch: Part No. 1870-A. Net weight: 2.1 lbs.

No. 176

No. 176 Carpet Layer's Mitre Box

This compact miter box includes straight and 45° angles needed by flooring installers, and really saves space in the tool box! The nickel-plated steel guides are highly accurate and case-hardened to resist wear even when used with a hacksaw. The wood base allows clean cuts through aluminum trim materials without dulling the hacksaw blade. Base includes synthetic rubber non-slip pad which helps the tool stay put in use and won't mark when placed on most surfaces. Net weight: 11 oz.

No. 368

No. 368 Deluxe Hacksaw Frame

This hacksaw has a sturdy steel frame with 3 ½" throat depth, high-impact plastic pistol grip handle, and comes with a 12" steel cutting blade. The frame accepts 10" or 12" hacksaw blades, and blades can be mounted in line with the frame or rotated to 90°, 180°, or 270° angles. Frame is plated to resist rust. Net weight: 1 ½ lbs.

No. 369

No. 369 12” Hacksaw Blades (2/card)

Includes two each 12" carbon steel hacksaw blades for use with the No. 368 Deluxe Hacksaw. The blades have 32 teeth per inch. They are good for mitering aluminum cap metal and other aluminum accessory trims using the No. 176 Miter Box, but can also be used to cut mild steel, cast iron, or copper. Net weight: 2 oz. / pack.

No. 855

No. 855 Wood Miter

The wood miter makes fast angle cuts in wood quarter round, eliminating the need for a chop saw. The stout 2 ½" long high carbon steel blade is strong enough and sharp enough to shear cut wood materials cleanly. The table includes a gauge for cutting straight, 22.5°, or 45° angles. The 22.5° angle gauge is used for making a "soft corner" shape, while the 45° angle is used to make square corners. The extra-long vinyl-coated handles provide adequate leverage for cutting. Blade is replaceable (No. 856). Net weight: 14 oz.

No. 856

No. 856 Wood Mitre Replacement Blade

Includes one each replacement blade for the Crain No. 855 Wood Mitre used to make angle cuts in wood quarter round. This stout, 2 ½" long blade is sharp enough and strong enough to shear cut wood materials cleanly. Made from high carbon steel for long life. Net weight: 1 oz.

No. 880

No. 880 Vinyl Mitre

The vinyl mitre makes clean, ultra-straight cuts in vinyl trims much faster than with a knife. Cut pieces come together perfectly to form more attractive corners. The tool includes a gauge for cutting the trim at a 45° angle to form a corner, or straight for butt cuts. The 2 3/8" long razor sharp blade is replaceable (No. 881). Net weight: 1 lb.

No. 881

No. 881 Replacement Blades (3)

Pack of three replacement blades for the No. 880 Vinyl Mitre used to make 45° cuts in vinyl trims for more attractive corners. These razor-sharp blades make clean, accurate cuts in the trim so that cut pieces come together perfectly. Comes in a plastic box that snaps closed for storage. Dimensions: length: 2.75", width: .75", thickness: .040". Pack weight: 1 oz.

No. 543

No. 543 Aviation Snips

These top quality compound leverage metal snips are great for making straight cuts in aluminum accessory trims or sheet metal when necessary. The alloy steel blades make up to 1 11/16" long cuts and provide the durability necessary for long-term performance. The handles include "soft-touch" grips which reduce twisting of the tool in the hand under forceful squeezing. Net weight: 1 lb.

No. 280

No. 280 H.D. Air Lifter

The Air Lifter moves heavy appliances up to 800 lbs. by generating high pressure jets through its perforated rubber load plates. Slide the load plates under the load, turn on the blower, and the air plates inflate to lift the load. The air jets beneath create a cushion of air that glides the load over hard surfaces like vinyl or hardwood without scratching. Comes with a set of four smooth polypropylene pads for moving the load plates over carpet. Saves time and reduces the risk of damaging new floors as well as injuries! Includes: 2 air plates, 2 horsepower blower with shoulder strap, T-connector, 3 hoses, 4 carpet pads, and 2 carrying bags. Volts: 120VAC - Amps: 7.5. Net weight: 30 lbs.

No. 017

No. 017 Metal Skat Skates

Crain Skat Skates are a pair of heavy-duty dollies that are adjustable in length for moving a wide variety of furniture and appliances. Each dolly in the set adjusts in length from 24" to 32". Each dolly has two 8" x 10" load pads and four pivoting casters beneath each pad. The 16 total casters allow the load to be easily moved or to change direction. The steel load bearing plates and telescoping tubes are welded together for durability. The soft urethane casters won't scratch or dent most floors. The maximum load capacity for the set is 1,000 lbs. Set weight: 20 lbs.

No. 024

No. 024 Rolling 24" Tool Box

This fully-featured yet lightweight 24" toolbox is made from advanced “structural foam” materials. The thick walls are very durable but weigh a lot less. The box rolls level with the ground thanks to a long, top-mounted pull handle that can be conveniently pulled along while walking. The inner tray has features that assist in carpet seaming, including a series of angled recesses which allow steam to escape while also evenly pressuring the seam. Includes a folding, recessed top carrying handle, and integral side handles for lifting with both hands. Case has three latches and a central hasp for locking. Net weight: 16 lbs.

No. 018

No. 018 Tile Dolly

This dolly is specifically designed for moving heavy boxes of VCT and other tile around the jobsite. It rolls and turns with up to five boxes of VCT on its deck or approximately 300 lbs. of material. It has five swiveling casters including one in the middle to help it turn and rotate. The casters have hardened steel brackets and soft urethane rollers that tend not to scratch most floors. The rugged 11" x 16" reinforced plastic deck includes a handle for grabbing and pulling. Maximum capacity: 300 lbs. Net weight: 3 3/4 lbs.

No. 124

No. 124 60" Carpet Cart

This cart has a full-sized 20 inch wide x 60 inch long bed that provides extra support for long and heavy rolls up to 1000 lbs. The tubular steel frame is reinforced with central steel plates for added durability. Four eyelets are provided for tying down the load. The large diameter 16" pneumatic tubed tires are tall and wide enough to roll up curbs or across gravel. Assembled size: length 60 inches, width 20 inches, height 18 inches. Weight capacity 1,000 lbs. Cart net weight: 42 lbs.

No. 015

No. 015 18" Vinyl Dolly

These 18" dollies are designed for moving and unrolling heavy rolls of vinyl on the jobsite up to 16" in diameter. Each of the three 18" long heavy gauge tubular steel rollers is mounted on double ball bearings to form a rolling bed for the material. Simply pull on the sheet, and the material feeds off the roll. The dolly has four non-marking rubber wheels mounted on the sturdy cast aluminum end frames which permit the dolly to be easily moved even when loaded. Net weight: 13 lbs.

No. 016

No. 016 36" Vinyl Dolly

These 36" dollies are designed for moving and unrolling heavy rolls of vinyl on the jobsite up to 16" in diameter. Each of the three 36" long heavy gauge tubular steel rollers is mounted on double ball bearings to form a rolling bed for the material. Simply pull on the sheet, and the material feeds off the roll. The dolly has four non-marking rubber wheels mounted on the sturdy cast aluminum end frames which permit the dolly to be easily moved even when loaded. Net weight: 20 lbs.

No. 354

No. 354 Pocket Tool Pouch

This leather pocket pouch is sized 4 ½" wide to slide easily into a standard-sized pants back pocket. Small items like a knife or row finder wedge securely in the 3" wide by 4 ½" deep inner pocket. An outer flap hooks over the pants pocket to protect it and to help keep the pouch from sliding out. Durable stitched and riveted construction. Outer dimensions: 4 ½" x 7 ½". Net weight: 4 oz.

No. 407

No. 407 Square Leather Tool Pouch

This square leather pouch hangs from the belt and has a deep 3 ¾" x 5 ½" rectangular pocket formed with 1" wide opening to quickly insert and remove larger items. The 2 ¼" wide slots go onto most belts. Durable riveted construction. Outer dimensions 4 ¼" x 7". Net weight: 4 oz.

No. 470

No. 470 Glue Bottle

The glue bottle is great for storing and spreading adhesives. The high-impact plastic bottle holds up to 16 oz. of adhesive. The metal lid includes an extendable brush to apply the adhesive that goes all the way to the bottom of the bottle. The narrow brush allows accurate application of adhesive, particularly in tight areas. The lid seals the bottle tight to extend the life of the adhesive. Net weight: 4 oz.

No. 570

No. 570 Clear Can

The Clear Can provides a great way to store nails and quickly dispense them on the job. The resealable lid is threaded on the clear plastic body and is easily removed to add nails. Squeezing the clear plastic body opens the lid to dispense the right amount of nails. After releasing, the lid closes and will not spill. Lid and bottom are made of thick, flexible vinyl and both are ribbed to prevent tearing. Sized at 2" diameter and 6" long, the Clear Can easily holds 250 stubby nails. Net weight: 2 oz.

No. 012

No. 012 Ward Standard Blades (12)

Includes a pack of 12 Standard Blades (Gundlach No. 12-WB) for the No. 005 Ward Handle (Gundlach No. 5). These specialized blades for sheetgoods installation can be mounted at steep angles for stiff commercial vinyls and thick linoleum, or less steep for regular materials. These blades are regular blades in comparison to the No. 013 (Gundlach 13-WB) Heavy Blades which are larger. The blades are packaged in a plastic tube with re-sealable lid for storage. Pack weight: 1 oz.

No. 013

No. 013 Ward Heavy Blade

Includes a pack of 12 Heavy Blades (Gundlach No. 13-WB) for the No. 005 Ward Handle (Gundlach No. 5). These specialized blades for sheetgoods installation can be mounted at steep angles for stiff commercial vinyls and thick linoleum, or less steep for regular materials. These blades are heavy blades in comparison to the No. 012 (Gundlach 12-WB) Regular Blades which are smaller. The blades are packaged in a plastic tube with re-sealable lid for storage. Pack weight: 1 oz.

No. 025A

No. 025A Airway Straight Blades (12)

Includes a vial of 12 Gundlach No. 25-AB trapezoidal-shaped straight blades for the Gundlach No. 6 Airway Knife (Crain No. 006). The Airway knife and blades are specialty blades for vinyl installation. These blades have a square central cutout that fits on a square boss in the knife that eliminates blade wobble. The blades are reversible and have two cutting edges. They come in a clear plastic vial with a re-sealable plastic lid for storage. Pack weight: 1 oz.

No. 026A

No. 026A Airway Hook Blades (12)

Includes a vial of 12 Gundlach No. 25-AB Hook Blades for the Gundlach No. 6 Airway Knife (Crain No. 006). The Airway knife and blades are specialty blades for vinyl installation. These blades have a square central cutout that fits on a square boss in the knife that eliminates blade wobble. The blades are reversible and have two hook- shaped cutting edges. They come in a clear plastic vial with a re-sealable plastic lid for storage. Pack weight: 1 oz.

No. 064

No. 064 Dexter Repl. Vinyl Blade

The No. 064 includes one each of the replaceable Dexter vinyl blade for use with the Dexter 10-D Handle (Crain No. 066). This blade is ground especially for cutting vinyl. It has a threaded tang type stem which threads into the Dexter 10-D Handle. The blade is made from high carbon steel, and is resharpenable. The No. 064 is the Dexter No. VX752 1/2 D (EDP No. 52170) Replaceable Vinyl Blade. Net weight: 1 oz.

No. 072

No. 072 Dexter "V" Sharp Hook Blades

These specialty Dexter hook blades for the No. 070 Dexter Custom Handle have an ultra-deep V sharp hook to produce clean cuts in felt-back vinyl. When used in combination with the angled blade carrier of the Dexter Custom Handle, they produce smooth cuts over long stretches of material. The hook also keeps the edge off the floor when cutting over concrete. Comes in a pack of five blades. These are the Dexter No. 72-5 “V” Sharp Hook Blades. Pack weight: 1 oz.

No. 073C

No. 073C Dexter Heavy-Duty Straight Blades (100)

These heavy-duty trapezoidal straight blades are made by Dexter. They are for use in the No. 070 Dexter Custom Handle (Dexter No. 7). They have a heavy duty 0.025" thickness. They have the standard profile of utility blades, but also have additional cutouts in the body for Allway knives that used these cutouts. Comes in a bulk pack of 100 blades. These are the Dexter No. 73-C Utility Blades. Pack weight: 13 oz.

No. 184

No. 184 Trimmer Blades (12)

Includes a pack of 12 carpet trimmer blades. They are for use in popular carpet wall trimmers including Crain No. 245 and No. 246. These blades are bevel ground on the top surface only to prevent the trimmer from rising and producing a fuller cut than desired. Install in the trimmer with the bevel side up. These blades produce an accurate height of cut which results in easier tucking of the carpet in the gully behind the tack strip. These blades come in a plastic box with a hinged lid that snaps closed for storage. Blade dimensions: length: 2.18", width: .75", thickness: .017". Pack weight: 1 ¼ oz.

No. 184C

No. 184C Trimmer Blades (100)

Includes a pack of 100 Personna® carpet trimmer blades. They are for use in popular carpet wall trimmers including Crain No. 245 and No. 246. These blades are bevel ground on the top surface only to prevent the trimmer from rising and producing a fuller cut than desired. Install in the trimmer with the bevel side up. These blades produce an accurate height of cut which results in easier tucking of the carpet in the gully behind the tack strip. These blades are individually wrapped in paper and come in a laminated paper box. Blade dimensions: length: 2.18", width: .75", thickness: .017". Pack weight: 11 oz.

No. 231

No. 231 Replacement Blade

This heavy-duty two inch wide blade is for use in the No. 230 Deluxe Floor Scraper. It is made from .090" thick high carbon steel to hold its edge and withstand repeated impact. It is tough enough to force its way through glued-down flooring materials, and sharp enough to scrape up thick adhesive residues. Includes one each blade only. Net weight: 5 oz.

No. 232

No. 232 3" Replacement Blade

This wider three inch wide blade for the No. 230 Deluxe Floor Scraper takes up wider sections of material. It is made from .090" thick high carbon steel to hold its edge and withstand repeated impact. It is tough enough to force its way through glued-down flooring materials, and sharp enough to scrape up thick adhesive residues. Includes one each blade only. Net weight: 5 oz.

No. 292C

No. 292C H.D. Utility Blades Disp. Pack (100)

Includes a dispenser pack of 100 heavy-duty utility blades. The plastic dispenser pack has a sliding tab on the bottom that dispenses one blade at a time for fast access. These blades can be used in most utility knives and any of the following Crain tools: No. 070 Dexter Custom Handle, No. 189 Hook Handle Utility Knife, No. 247 Multi-Purpose Wall Trimmer, No. 265 Stand-Up Cutter, No. 290 Seam Cutter Plus, No. 300 Loop Pile Cutter, No. 304 Versa-Cutter, No. 727 Delphin Knife, No. 728 Folding Utility Knife, No. 730 Utility Knife, and No. 732 Extra-Grip Utility Knife. Blade dimensions: length: 2.40", width: .75", thickness: .025". Pack weight: 1 lb.

No. 295C

No. 295C Heavy-Duty Utility Blades (100)

Includes a pack of 100 Personna® heavy-duty utility blades which are individually wrapped in paper. These blades can be used in most utility knives and any of the following Crain tools: No. 070 Dexter Custom Handle, No. 189 Hook Handle Utility Knife, No. 247 Multi-Purpose Wall Trimmer, No. 265 Stand-Up Cutter, No. 290 Seam Cutter Plus, No. 300 Loop Pile Cutter, No. 304 Versa-Cutter, No. 727 Delphin Knife, No. 728 Folding Utility Knife, No. 730 Utility Knife, and No. 732 Extra-Grip Utility Knife. These blades are individually wrapped in paper and come in a laminated paper box. Blade dimensions: length: 2.40", width: .75", thickness: .025". Pack weight: 1 lb. 3 oz.

No. 299Y

No. 299Y Top Cutter Repl. Blades (10)

Includes a pack of 10 blades for the discontinued Crain No. 298 Top Cutter. When used with the Top Cutter, this elongated blade can double cut carpet from the face. For use with the Crain No. 298 Top Cutter only. Blade dimensions: length: 3.00", width: .745", thickness: .025". Pack weight: .20 lb.

No. 300Y

No. 300Y Loop Pile Cutter Repl. Blades (10)

Includes a pack of 10 replacement blades for the Crain No. 300 Loop Pile Cutter. These blades have two holes for a blade holding screw on early models of the No. 300 (black plastic body), but also work in later models of this cutter. When used in the No. 300, these blades cut the carpet from the backing, reducing the shearing of yarns and wadding up of carpet in the cutter. The two screw holes make these blades reversible for added life. These blades come in a plastic box with a hinged lid that snaps closed for storage. Blade dimensions: length: 2.31", width: .75", thickness: .025". Pack weight: .10 lb.

No. 306C

No. 306C Regular-Duty Slotted Razor Blades

Includes a pack of 100 Personna® regular-duty (.015" thick) round-edge slotted razor blades which are individually wrapped in paper. Regular duty blades are economical and the reduced thickness fits certain older model Crain tools that take a thinner blade (such as Crain No. 124 Flipper Knife or older No. 301 Cushion Back Cutter or No. 302 Cushion Lock Cutter). Not recommended for use in newer Crain tools which are designed for No. 308C / No. 309C heavy duty blades (.017" thick). These blades are individually wrapped in paper and come in a laminated paper box. Blade dimensions: length: 2.25", width: .75", thickness: .015". Pack weight: 10 oz.

No. 308C

No. 308C Heavy-Duty Round Edge Slotted Razor Blades

Includes a pack of 100 Personna® heavy-duty (.017 thick) round edge slotted razor blades which are individually wrapped in paper. Round edge blades are preferred by many carpet installers because the round corner rides on the subfloor without digging in and creating extra resistance. These blades can be used in the following Crain tools: Nos. 191, 217, 247, 290, 300, 304, 301, 302, 303, 330, 720, 735, 725, 726. The individually wrapped blades come in a laminated paper box. Blade dimensions: length: 2.25", width: .75", thickness: .017". Pack weight: 12 oz.

No. 309C

No. 309C Heavy-Duty Square Edge Slotted Razor Blades

Includes a pack of 100 Personna® heavy-duty (.017 thick) square edge slotted razor blades which are individually wrapped in paper. Square edge blades provide a sharp, precise point for starting a cut with the knife. They also cut to full depth when used in seam cutters such as the Crain No. 301 Cushion Back Cutter and No. 302 Cushion Back Cutter. These blades can be used in the following Crain tools: Nos. 191, 217, 247, 290, 300, 304, 301, 302, 303, 330, 720, 735, 725, 726. The individually wrapped blades come in a laminated paper box. Blade dimensions: length: 2.25", width: .75", thickness: .017". Pack weight: 12 oz.

No. 321

No. 321 Vinyl Wall Trimmer Blades (3)

Includes a pack of three hook blades for the No. 321 Vinyl Wall Trimmer. The reversible blade includes two cutting hook edges. The blades come in a plastic box with a hinged lid for storage. Blade dimensions: length: 2.30", width: .50", thickness: .025". Pack weight: 1 oz.

No. 351

No. 351 Stripper Blades (10)

Pack of 10 blades for the No. 350 Floor Stripper and No. 360 Pro Stripper. These blades are .020" thick and provide the right flexibility for fine floor prep. work. They work especially well for removal of adhesive residue from concrete floors. Comes in a vial of ten blades with a resealable cap with hanging hole. Dimensions: Length: 4.00", Width: .560", thickness: .020". Net weight: 2 oz.

No. 351C

No. 351C Stripper Blades (100)

Bulk pack of 100 blades for the No. 350 Floor Stripper and No. 360 Pro Stripper. These blades are .020" thick and provide the right flexibility for fine floor prep. work. They work especially well for removal of adhesive residue from concrete floors. Comes in a bulk pack vial of 100 blades with a resealable cap with hanging hole. Dimensions: Length: 4.00", Width: .560", thickness: .020". Net weight: 2 oz.

No. 353Y

No. 353Y Grout Saw Replacement Blades (2)

This hand saw is used for removing old or damaged grout. The angled steel handle bracket keeps the hand from contacting the floor during the sawing motion. Comes with one carbide blade coated with carbide grit for cutting out grout between tiles, and one steel-toothed blade for heavy cleanout work after using the carbide blade. The steel-toothed blade can be used in combination with the carbide blade for wider grout joints or to protect walls when removing grout close up to a wall. Minimum grout joint width: 1/8”. Net weight: 4 oz.

No. 376

No. 376 Big Scraper Blades (3)

Pack of three replacement blades for use with the Crain No. 375 Big Scraper or No. 375S Short Big Scraper. Wide 8" Blade removes the widest section of material of any Crain hand scraper blade. Good for hand scraping of heavier adhesive residue. Comes in a plastic vial of three blades with resealable cap for storage. Dimensions: 8" long x .750" wide x .037" thick. Net weight: 4 oz.

No. 377

No. 377 Big Scraper Blades (9)

Pack of nine replacement blades for use with the Crain No. 375 Big Scraper or No. 375S Short Big Scraper. Wide 8" Blade removes the widest section of material of any Crain hand scraper blade. Good for hand scraping of heavier adhesive residue. Comes in a plastic vial of nine blades with resealable cap for storage. Dimensions: 8" long x .750" wide x .037" thick. Net weight: 4 oz.

No. 391

No. 391 Inertial Scraper Blades (10)

Pack of ten replacement blades for the Crain No. 390 Inertial Scraper. These wide 5" blades are made with the same .037" thickness as our heavy-duty Big Scraper blades. These stout blades can be used to scrape up hard spots. They come in a plastic vial of ten blades with a resealable cap. Dimensions: 5" long, .750" wide, .037" thick. Pack weight: 7 oz.

No. 451

No. 451 Strip Cutter Blades (12)

This package of replacement blades for the Crain No. 450 Deluxe Strip Cutter includes twelve blades. When used in the No. 450 Deluxe Strip Cutter, they can cut wide architectural strip straight in a single cut. They can also cut regular strip straight or diagonally in one cut. The packaging includes a clear plastic box with a lid that snaps shut to protect blades in storage. Blade dimensions: length 1.87", width .48", thickness .040". Net weight: 1 oz.

No. 523Y

No. 523Y 23" Seammate Repl. Blade

Includes three replacement blades for the Crain Seammate doorway seaming tool. Each blade has one 23" long razor sharp edge for scoring the carpet's backing at the location of a doorway seam. When used with the Seammate, it marks a straight line on the carpet's backing which can be trace cut with a knife. Blade dimensions: length: 23.27", width: .560", thickness: .020". Pack weight: .30 lb.

No. 881

No. 881 Replacement Blades (3)

Pack of three replacement blades for the No. 880 Vinyl Mitre used to make 45° cuts in vinyl trims for more attractive corners. These razor-sharp blades make clean, accurate cuts in the trim so that cut pieces come together perfectly. Comes in a plastic box that snaps closed for storage. Dimensions: length: 2.75", width: .75", thickness: .040". Pack weight: 1 oz.

No. 856

No. 856 Wood Mitre Replacement Blade

Includes one each replacement blade for the Crain No. 855 Wood Mitre used to make angle cuts in wood quarter round. This stout, 2 ½" long blade is sharp enough and strong enough to shear cut wood materials cleanly. Made from high carbon steel for long life. Net weight: 1 oz.

No. 956

No. 956 Pull Hand Groover Blades (3)

These U-shaped replacement blades for the No. 955 Pull Hand Groover come in a pack of three each. They are precision formed from high carbon steel, heat-treated, and hand sharpened. The locator hole above the screw hole keeps the blade rigidly in place on the blade holder of the Crain No. 955 Pull Hand Groover. The standard shape of this blade allows it to be used on other popular pull hand groovers as well. Net weight: 1/2 oz. / pack.

No. 966

No. 966 Skiving Knife Repl. Blade

Includes one each replacement blade for the No. 965 Skiving Knife used for trimming excess heat welding rod flush at the seam. This replaceable blade is flexible to eliminate gouging high spots which can occur with quarter moon knives. It also eliminates difficult resharpening of quarter moon knives. Net weight: 1/4 oz.

No. 967

No. 967 Skiving Knife Repl. Blades (5)

Includes a pack of five replacement blades for the No. 965 Skiving Knife used for trimming excess heat welding rod flush at the seam. These replaceable blades are flexible to eliminate gouging of high spots which can occur with quarter moon knives. They also eliminate difficult resharpening of quarter moon knives. Net weight: 1 1/4 oz.

No. 984

No. 984 Hand Groover Repl. Blades (10)

This is a pack of ten replacement blades for the No. 983 Hand Groover which is used to form a U-shaped groove at the seam line for welding. The blades have U-shaped edges ground on both sides. The blades come in a plastic box with a lid that snaps shut for storage. Net weight: 1 oz.

No. 996X

No. 996X Hook Blades (15)

Includes a pack of 15 high-quality German-made hook blades. The hook shape keeps the cutting edge off the floor when cutting over concrete. They are also good for following score lines in linoleum and making long rough cuts in sheet vinyl materials. These blades come in a plastic box with a hinged lid that snaps closed for storage. They can be used in most utility knives and any of the following Crain tools: No. 189 Hook Handle Utility Knife, No. 247 Multi-Purpose Wall Trimmer, No. 265 Stand-Up Cutter, No. 727 Delphin Knife, No. 728 Folding Utility Knife, No. 730 Utility Knife, and No. 732 Extra-Grip Utility Knife. Pack weight: 2 oz.

No. 997

No. 997 Personna® Deep Hook Blades (10)

Includes a pack of 10 Personna® deep hook blades. The hook shape keeps the cutting edge off the floor when cutting over concrete. They are also good for following score lines in linoleum and making long rough cuts in sheet vinyl materials. They can be used in most utility knives and any of the following Crain tools: No. 189 Hook Handle Utility Knife, No. 247 Multi-Purpose Wall Trimmer, No. 265 Stand-Up Cutter, No. 727 Delphin Knife, No. 728 Folding Utility Knife, No. 730 Utility Knife, and No. 732 Extra-Grip Utility Knife. Blade dimensions: length: 2.0", width: .75", thickness: .025". Pack weight: 2 oz.

No. 1174-A

No. 1174-A Instant Repair Tool Blades (4)

Includes a pack of four replacement blades for the Crain No. 174 Instant Repair Tool used to cut circular holes in carpet for repairs. The four blades in this pack can replace all four blades in the tool if desired. Blades have a slot that accepts the blade screws on the tool. Blade dimensions: length: 1.035", width: .50", thickness: .020". Pack weight: 0.2 oz.

No. 420

No. 420 Professional Trowel

The No. 420 is a 1/16” open x 1/16” flat x 1/16” deep square-notched trowel. The front edge is angled back 10° for clearance when spreading close to the wall. The wooden handle is curved for comfortable grip. The handle bracket is welded to the spring steel blade. Add "L" to the No. 420 for left-handed model (i.e. No. 420L). Net weight: 1 lb.

No. 420L

No. 420L Professional Trowel, Left

The No. 420L is a 1/16” open x 1/16” flat x 1/16” deep square-notched trowel that is notched on the left side of the blade for left-handed users. The front edge is angled back 10° for clearance when spreading close to the wall. The wooden handle is curved for comfortable grip. The handle bracket is welded to the spring steel blade. Net weight: 1 lb.

No. 421

No. 421 Professional Trowel

The No. 421 is a 1/16” open x 1/4” flat x 1/16” deep V-notched trowel. The front edge is angled back 10° for clearance when spreading close to the wall. The wooden handle is curved for comfortable grip. The handle bracket is welded to the spring steel blade. Net weight: 1 lb.

No. 422

No. 422 Professional Trowel

The No. 422 is a 1/16” open x 1/32” flat x 1/32” deep U-notched trowel. The front edge is angled back 10° for clearance when spreading close to the wall. The wooden handle is curved for comfortable grip. The handle bracket is welded to the spring steel blade. Add "L" to the No. 422 for left-handed model (i.e. No. 422L). Net weight: 1 lb.

No. 422L

No. 422L Professional Trowel, Left

The No. 422L is a 1/16” open x 1/32” flat x 1/32” deep U-notched trowel that is notched on the left side of the blade for left-handed users. The front edge is angled back 10° for clearance when spreading close to the wall. The wooden handle is curved for comfortable grip. The handle bracket is welded to the spring steel blade. Net weight: 1 lb.

No. 423

No. 423 Professional Trowel

The No. 423 is a 1/8” open x 1/16” flat x 1/8” deep V-notched trowel. The front edge is square and notched for "cutting in" or spreading adhesive in tight areas like corners. The wooden handle is curved for comfortable grip. The handle bracket is welded to the spring steel blade. Add "L" to the No. 423 for left-handed model (i.e. No. 423L). Net weight: 1 lb.

No. 423L

No. 423L Professional Trowel, Left

The No. 423L is a 1/8” open x 1/16” flat x 1/8” deep V-notched trowel that is notched on the left side of the blade for left-handed users. The front edge is square and notched for "cutting in" or spreading adhesive in tight areas like corners. The wooden handle is curved for comfortable grip. The handle bracket is welded to the spring steel blade. Net weight: 1 lb.

No. 424

No. 424 Professional Trowel

The No. 424 is a 3/32” open x 3/32” flat x 3/32” deep V-notched trowel. The front edge is angled back 10° for clearance when spreading close to the wall. The wooden handle is curved for comfortable grip. The handle bracket is welded to the spring steel blade. Net weight: 1 lb.

No. 425

No. 425 Professional Trowel

The No. 425 is a 1/4” open x 3/16” deep V-notched trowel. The front edge is square and notched for "cutting in" or spreading adhesive in tight areas like corners. The wooden handle is curved for comfortable grip. The handle bracket is welded to the spring steel blade. Net weight: 1 lb.

No. 426

No. 426 Professional Trowel

The No. 426 is a 1/4” open x 1/4” flat x 1/4” deep square-notched trowel. The front edge is square and notched for "cutting in" or spreading adhesive in tight areas like corners. The wooden handle is curved for comfortable grip. The handle bracket is welded to the spring steel blade. Net weight: 1 lb.

No. 427

No. 427 Professional Trowel

The No. 427 is a 1/2” open x 1/2” deep V-notched trowel. The front edge is square and notched for "cutting in" or spreading adhesive or mortar in tight areas like corners. The wooden handle is curved for comfortable grip. The handle bracket is welded to the spring steel blade. Net weight: 1 lb.

No. 428

No. 428 Professional Trowel

The No. 428 is a 1/4” open x 1/4” flat x 3/8” deep square-notched trowel. The front edge is square and notched for "cutting in" or spreading mortars and adhesives in tight areas like corners. The wooden handle is curved for comfortable grip. The handle bracket is welded to the spring steel blade. Net weight: 1 lb.

No. 429

No. 429 Professional Trowel

The No. 429 is a 1/2” open x 1/2” flat x 1/2” deep square-notched trowel. The front edge is square and notched for "cutting in" or spreading mortars and adhesives in tight areas like corners. The wooden handle is curved for comfortable grip. The handle bracket is welded to the spring steel blade. Net weight: 1 lb.

No. 430

No. 430 Professional Trowel

The No. 430 is a 1/8” open x 1/16” flat x 1/8” deep U-notched trowel. The front edge is angled back 10° for clearance when spreading close to the wall. The wooden handle is curved for comfortable grip. The handle bracket is welded to the spring steel blade. Net weight: 1 lb.

No. 431

No. 431 Professional Trowel

The No. 431 is a 1/16” open x 1/16” flat x 1/16” deep V-notched trowel. The front edge is angled back 10° for clearance when spreading close to the wall. The wooden handle is curved for comfortable grip. The handle bracket is welded to the spring steel blade. Net weight: 1 lb.

Pages

Subscribe to Other